A lot of access points, even consumer-grade ones, have this option. It’s usually accomplished via predefined firewall rules on the access points themselves.
Consumer-grade access points usually let you have just one isolated guest network, whereas fancier ones (Omada, Unifi, Ruckus, Aruba, etc) usually let you enable isolation for any SSID (ie the “guest network” is no different from any other SSID)
The APs know who the Wi-Fi clients are and just drops traffic between them. This is called client/station isolation. It’s often used in corporate to 1) prevent wireless clients from attacking each other (students, guests) and 2) to prevent broadcast and multicast packets from wasting all your airtime. This has the downside of breaking AirPlay, AirPrint and any other services where devices are expected to talk to each other.
If there’s an option on the AP to not permit link local routing within a vlan/ssid, that will force all traffic up to the firewall. Then you can block intrazone traffic at the firewall level for that vlan.
I’ve seen this in Meraki hardware where it’s referred to as “client isolation”. Ubiquiti might be able to do this too.
I used to have a Netgear Nighthawk router/AP I bought from Costco, and if I remember correctly, its guest network automatically isolated guests from other guests. This router didn’t support VLANs so I think it was just a bunch of firewall rules.
I’m not seeing anything there that says guests can’t see other guests - quite the opposite.
guests connected to your Hotspot Portal will be isolated from all other networks except the one they are assigned to.
Guests on this network are able to access the internet, and communicate with the UniFi gateway to obtain a DHCP lease and resolve names using DNS
I suppose a switch could be configured to prevent traffic going to other ports, which is how I would assume this would have to be done. This functionality would have to exist in the access point, I guess?
Does UniFi have a feature to isolate devices from each other on the same subnet? Seems like it would require some kind of Layer 2 routing?
How do you accomplish this isolation since they’re on the same subnet/broadcast domain? Is it a feature of the hardware you’re using?
A lot of access points, even consumer-grade ones, have this option. It’s usually accomplished via predefined firewall rules on the access points themselves.
Consumer-grade access points usually let you have just one isolated guest network, whereas fancier ones (Omada, Unifi, Ruckus, Aruba, etc) usually let you enable isolation for any SSID (ie the “guest network” is no different from any other SSID)
Isolated guest networks I get, but isolating guests from other guests on the same subnet/isolated net is what I haven’t seen.
The APs know who the Wi-Fi clients are and just drops traffic between them. This is called client/station isolation. It’s often used in corporate to 1) prevent wireless clients from attacking each other (students, guests) and 2) to prevent broadcast and multicast packets from wasting all your airtime. This has the downside of breaking AirPlay, AirPrint and any other services where devices are expected to talk to each other.
If there’s an option on the AP to not permit link local routing within a vlan/ssid, that will force all traffic up to the firewall. Then you can block intrazone traffic at the firewall level for that vlan.
I’ve seen this in Meraki hardware where it’s referred to as “client isolation”. Ubiquiti might be able to do this too.
I used to have a Netgear Nighthawk router/AP I bought from Costco, and if I remember correctly, its guest network automatically isolated guests from other guests. This router didn’t support VLANs so I think it was just a bunch of firewall rules.
For Unifi devices you setup a Virtual Network then assign the guests to that. https://help.ui.com/hc/en-us/articles/115000166827-UniFi-Hotspot-Portal-and-Guest-WiFi
I’m not seeing anything there that says guests can’t see other guests - quite the opposite.
I suppose a switch could be configured to prevent traffic going to other ports, which is how I would assume this would have to be done. This functionality would have to exist in the access point, I guess?
Does UniFi have a feature to isolate devices from each other on the same subnet? Seems like it would require some kind of Layer 2 routing?
It does. I have it enabled and tested. “Client Device Isolation.” It’s enabled per SSID.
Oh, neat. I’ll have to look into it.
Thanks!
Unifi out of the box settings.